Cisco AIR-ANT2568VG-N Netzwerk-Antenne Omnidirektionale Antenne N-Typ 8 dBi
Abholung/ Versand möglich am Freitag, den 11.10
Zustellung zw. 14.10 - 16.10
Cisco AIR-ANT2568VG-N. Antenne Zunahmeniveau (max): 8 dBi, Frequenzband: 2400 - 2483, 5150 - 5925 GHz, Antenna Zuwachs (2.4 GHz): 6 dBi. Antennentyp: Omnidirektionale Antenne, Antenne Steckertyp: N-Typ, Polarisation: Vertikale Polarisation. Höhe: 377 mm, Durchmesser: 3,81 cm, Gewicht: 204,1 g. Menge pro Packung: 1 Stück(e)
Passendes Zubehör:
Beschreibung
Cisco AIR-ANT2568VG-N Netzwerk-Antenne Omnidirektionale Antenne N-Typ 8 dBi
Cisco Aironet Dual-Band Omnidirectional Antenna AIR-ANT2568VG-N is designed for outdoor use with Cisco Aironet Outdoor Access Points hereafter referred to as access points with radios operating in the 2.4-GHz and 5-GHz frequency bands.
Installation Notes
The antenna is designed to connect to a dedicated antenna port on the access point. No special tools are required to install the antenna.
The antenna is resistant to the full range of outdoor environments. After the antenna is attached to the access point, seal the connections to prevent moisture and other weathering elements from affecting performance. Cisco recommends using a coax seal such as CoaxSeal for outdoor connections. Silicone sealant or electrical tape are not recommended for sealing outdoor connections.
Choosing a Mounting Location
The antenna is designed to create an omnidirectional broadcast pattern. To achieve this pattern, the access point should be mounted clear of any obstructions to the sides of the radiating element. If the mounting location is on the side of a building or tower, the antenna pattern is degraded on the building or tower side.
Generally, the higher an antenna is above the ground, the better it performs. A practice is to install your antenna about 5 to 10 ft 1.5 to 3 m above the roof line and away from all power lines and obstructions.
Tools and Equipment Required
No tools are required to mount the antenna to the access point. However, you may need a -in. 19-mm open end or combination wrench or adjustable wrench to remove the antenna port covers.
For information about tools required to mount the access point, see the appropriate access point documentation.
Mounting the Antenna
To connect the antenna to the access point, follow these steps:
Step 1 If necessary, remove the antenna port cover.
Step 2 Align the antennas N connector with the appropriate antenna port.
Step 3 Gently push the antenna into the port.
Step 4 Tighten the antenna hand tight.
Diese Artikel könnten Sie auch interessieren:
Datenblatt
| Leistungen | |
|---|---|
| Antenne Zunahmeniveau max: | 8 dBi |
| Frequenzband: | 2400 - 2483, 5150 - 5925 GHz |
| Antenna Zuwachs 2.4 GHz: | 6 dBi |
| Antenna Zuwachs 5 GHz: | 8 dBi |
| Impedanz: | 50 Ohm |
| Merkmale | |
| Antennentyp: | Omnidirektionale Antenne |
| Antenne Steckertyp: | N-Typ |
| Polarisation: | Vertikale Polarisation |
| Internationale Schutzart IP-Code: | IP67 |
| Betriebsbedingungen | |
| Betriebstemperatur: | -30 - 70 °C |
| Temperaturbereich bei Lagerung: | -40 - 85 °C |
| Gewicht und Abmessungen | |
| Höhe: | 377 mm |
| Durchmesser: | 3,81 cm |
| Gewicht: | 204,1 g |
| Verpackungsdaten | |
| Verpackungsbreite: | 152,4 mm |
| Verpackungstiefe: | 482,6 mm |
| Verpackungshöhe: | 50,8 mm |
| Paketgewicht: | 362,81 g |
| Lieferumfang | |
| Menge pro Packung: | 1 Stücke |
| Logistikdaten | |
| Warentarifnummer HS: | 85177100 |
| Ursprungsland: | China |
Hinweis: Die Beschreibung und das Datenblatt werden von Icecat zur Verfügung gestellt. Für die Richtigkeit und Vollständigkeit der aufgeführten Daten wird keine Haftung übernommen.
* Alle Preis zzgl. Versandkosten soweit nicht anders angegeben und gelten nur für Lieferungen nach Deutschland!